Introduction to Pipeline Silencers:

Pipeline silencers (silencers) are mainly used for silencing the steam emissions of thermal equipment such as boilers and steam turbines in the power generation department.

Purpose of pipeline muffler:

The noise emitted by steam emissions from steam boilers and related thermal equipment can reach up to 130 decibels, far exceeding the values specified in the Industrial Enterprise Noise Hygiene Standard issued by us. (For example, superheated steam with a gauge pressure of 1kg/cm2 can reach a velocity of 570-600 meters/second when discharged into the atmosphere through a hole, while for saturated steam, its velocity can also reach 470-480 meters/second. When such high-speed steam is discharged into the atmosphere, it causes high noise due to exceeding the sound velocity of 340 meters/second.). Noise reduction - results in meeting the requirements of the Industrial Enterprise Noise Hygiene Standards.

Pipeline silencer -:

Pipeline silencers (silencers) are mainly used for silencing the steam emissions of thermal equipment such as boilers and steam turbines in the power generation department. At the same time, it is also used for boiler steam emissions and other gas silencing emissions in industries such as petroleum, chemical, metallurgical, and textile. A suppressor is a device that prevents sound transmission and allows airflow to pass through, which is an important measure to eliminate steam emission power noise. To measure the effectiveness of an exhaust suppressor, the following three aspects are mainly considered:

1. The noise reduction capacity of the pipeline muffler can meet the requirements of the Industrial Enterprise Noise Hygiene Standard.

2. Adaptability of pipeline silencers; (i.e. adapting to low spectrum broadband and high temperature and high pressure).

3. The structure of pipeline eliminators. (Reasonable size, low construction, long, etc.).

The boiler steam in the power generation department not only has high temperature and high pressure, but also a wide emission frequency bandwidth. Relying solely on small hole noise reduction is not enough. The auxiliary exhaust steam eliminator is developed based on the principle of composite noise reduction of resistance, spray, and resistance. It has a large noise reduction amount, a wide adaptability frequency band, and is designed specifically for various parameters such as low pressure, - pressure, sub high pressure, high pressure, subcritical, and - critical, The silencer is made of stainless steel (1Cr18Ni9Ti, 12Cr1MoV) and is easy to install.

Principle of pipeline muffler:

The boiler exhaust steam eliminator is manufactured based on the principle of micro perforated plate noise reduction. The steam discharge from power plant boilers generally has a high flow rate, which has a significant impact on the noise reduction of small holes. So we need to control the flow, and the steam that passes through flow control will enter the expansion chamber and then be further depressurized and silenced. After the steam is depressurized by a large volume, it forms low-pressure steam and sprays out. During this process, the airflow is ejected through a small aperture. After spraying, the sound power of each octave band has decreased, and the frequency of sound pressure has been raised to above 20000Hz, greatly weakening its noise. But some frequencies of secondary noise still need to be further silenced. We are installing sound-absorbing cotton knots outdoors for expansion, which are designed based on the spectrum of residual noise emitted by the pressure reducing body, to effectively absorb residual noise. After the user installs according to the requirements, the total noise reduction should reach 30-60 decibels to meet the requirements.

Ordering selection:

The muffler is designed according to the user's emission target and requirements. Therefore, only when the production meets the emission target and parameters can significant noise reduction be achieved.

Therefore, when ordering consumers, the following information must be provided:

(1) Steam emissions - low (T/h), as well as pressure and temperature.

(2) Object of use (such as for boiler steam displacement or safety valve discharge, etc.).

(3) Outer diameter and wall thickness of exhaust pipe.

你可能喜歡看：

Blower silencer

11-25 1018

The blower muffler is mainly suitable for reducing the intake and exhaust noise of Roots series and axial flow series fans. The blower muffler can also be used for noise reduction of exhaust pipes and other high-pressure fans, with a noise reduction amount of 10-20dB (A) and a pressure loss of less than 500Pa.

Blow pipe silencer

08-20 978

Blow pipe silencers can be used to eliminate the noise generated by boilers and Pipelines during blowing. Box type blow pipe silencers are divided into upper exhaust and partial exhaust, with the upper exhaust type being a box structure and the partial exhaust type being a circular structure.

Centrifugal fan silencer

11-26 976

The centrifugal fan muffler is developed based on the principle of soundproof sheet noise reduction. This type of muffler has good acoustic performance and good aerodynamic performance; Reasonable in structure and easy to install, it is a honeycomb type muffler with high wind resistance. It adopts a chamber resistant adhesive straight pipe channel and a cross shaped sound-absorbing plate form.

Safety valve silencer

08-20 885

The TA type exhaust safety valve silencer is suitable for the safety valves of pressure devices such as PCV/ERV safety valves (power release valves), drum safety valves, superheater safety valves, and reheater safety valves in power plant boilers. The safety valve muffler adopts the principle of spray impedance composite noise reduction, which replaces the smaller diameter control hole with a large hole expansion.

Steam silencer

11-26 880

Steam silencers are used for a wide range of steam emission objects in thermal equipment. Various specifications of boiler steam silencers can be designed and manufactured based on the user's extracted steam output, steam pressure, and connection size.

Small hole injection silencer

11-26 850

A small hole injection muffler is also known as a diffuser. It sprays gas from high-pressure vessels through several layers of small orifice plates to reduce noise. To prevent clogging of small holes and the difficulty of processing small holes, the diameter of small holes can be selected within the range of 1-3 millimeters (which should meet the condition of b>=8d)

Venting silencer

08-20 834

A venting muffler is designed and developed to suppress noise production during factory Pipeline venting and exhaust. The types of mufflers are divided into six main types: vent mufflers, impedance composite mufflers, micro perforated plate mufflers, small hole mufflers, and existing mufflers.

Chimney silencer

11-25 778

Chimney noise disturbing the public, how to - chimney muffler, using chimney muffler - chimney noise management. Chimney noise, such as in chemical plants and cement plants, has high chimneys and high air vents. The noise from the air vents presents a low-frequency buzzing sound, which affects a considerable range of the surrounding environment.

Combination fan silencer

11-26 776

The combination type fan muffler (combination type composite muffler) mainly has a small hole type muffler inserted inside the fan muffler to achieve the desired effect, and the combination mode can be selected as needed. Welcome - Customers come to design and manufacture, or contact us to help you design.

Induced draft fan silencer

11-26 705

The induced draft fan silencer is mainly suitable for reducing the intake noise of Roots series fans, and can also be used for noise reduction of exhaust pipes and other high-pressure fans. The induced draft fan has a noise reduction capacity of 15-30dB (A) and a pressure loss of less than 500Pa.