The oil injectors produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd. generally consist of nozzle filters, expansion pipes, inlet pipes, etc., and are installed on the main oil pump. When the pressure oil is sprayed out at high speed through the nozzle, a vacuum is formed at the nozzle. By utilizing the suction effect of the free jet, the oil in the tank is brought into the diffusion tube for deceleration and pressure increase, and then discharged at a certain pressure. Enable the main oil pump to have a certain pressure and improve the reliability of its operation.

The functions of lubrication oil tank injector 1 # and injector 2 # for steam turbines:

-The general unit is equipped with two oil injectors, which are divided into an oil injector and a second oil injector, also known as an oil injector. The second oil injector is installed below the liquid level in the lubricating oil tank, and when the unit is put into operation at or near the rated speed. The oil injector consists of a nozzle, a mixing chamber, a diffusion tube, etc. After the pressure oil from the main oil pump passes through the nozzle, the oil velocity increases and forms a low-pressure zone in the chamber. The oil in the tank is pumped into the injector chamber, and then it is carried by a high-speed oil belt into the diffuser throat. The velocity decreases in the diffuser and is converted into pressure energy. Then, through an oil cooler, it is sent through a pipe to the bearing manifold and the main oil pump suction port. Diffusion - equipped with a rocker check valve at the back to prevent oil from flowing back from the system. A check plate is installed on the surface of the oil tank in the chamber to prevent backflow into the oil tank during the operation of the bearing oil pump. To prevent foreign objects from entering the oil injector, a detachable perforated steel plate filter screen is installed on the oil suction side of the injector. The oil injector is one of the essential equipment in the lubricating oil system of the steam turbine generator set. In the lubricating oil system of the steam turbine generator set, the oil injector equipment can be divided into oil supply injectors and lubricating oil supply injectors according to its working purpose. Its working medium is L-TSA 32 turbine oil, with a working oil temperature of 45 ℃~65 ℃. When the unit reaches or approaches the rated speed, it is put into operation.

1. Fuel injector:

During normal operation of the unit, sufficient oil is provided to the main oil pump, with a portion of the pressure oil at the outlet of the main oil pump as its power oil.

2. Lubricating oil injector:

During the normal operation of the unit, lubricating oil is provided to the bearings of the steam turbine generator set, and its power oil is still part of the outlet of the main oil pump.

The installation of oil injectors requires attention to the following two aspects:

3. Assembly and installation:

The installation of the oil injector and its impact on energy are different. When installing the nozzle of the oil injector and lubricating oil injector, the nozzle bracket and inlet pipe flange must be tightened to ensure high-pressure oil leakage. The flatness and smoothness of all adhesive surfaces should be -.

4. Maintenance and upkeep:

When the oil injector is transported to the site after leaving the factory, if it is not immediately put into use, it needs to be repainted and sealed for protection. If it cannot be installed or filled with oil within two months of arriving at the site, it should be installed. The oil injector must be disassembled and inspected to remove rust and dirt. During the overhaul of the unit, the oil injector needs to be disassembled and inspected, and the nozzle should not be inspected. The surface roughness of the spray hole should reach the surface roughness (arithmetic mean of the contour deviation within the sampling length) R α The upper limit value is 3.2 microns. If there are any scratches or indentations, they need to be replaced.

你可能喜歡看：

Installation and working engineering of coal powder sampler

11-25 1018

The installation and operation of The coal powder sampler and mobile coal powder sampler of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. drill holes on The flue, extend The sampling tube into The flue, and make The sampling head face The direction of The incoming smoke flow.

The purpose of fly ash sampler

11-25 933

The purpose and function of The fly ash sampler produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is that The carbon content of boiler fly ash is an important indicator reflecting The combustion rate of coal-fired boilers in Thermal power plants.

Assembly and installation of oil injectors

11-25 921

The oil supply and lubrication oil injectors are completely identical in structure, mainly composed of orifice nozzles, diffusion tubes, sleeves, filters, etc.

The function of an oil injector is to use a small amount of lubricating oil as power

08-20 866

The function of The oil injector of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is to use a small amount of lubricating oil as power, suck in a large amount of oil, and supply lubricating system and main oil pump with oil at a certain pressure.

The principle of steam jet pump and steam injector

11-25 854

A steam injector is a device that is powered by steam and is needed in modern engineering. It does not require electricity, has no moving or rotating parts, is simple in system, and works reliably, so it is used.

The basic principle of lubricating oil system injectors

11-25 810

The oil injector is composed of a nozzle, a filter screen, an expansion pipe, and an inlet pipe. In addition to supplying The inlet oil of The centrifugal main oil pump, it also supplies lubricating oil system and sealing oil system oil.

Portable constant velocity fly ash sampler for regular coal powder sampling on The air and coal powder pipeline

08-20 779

The portable constant velocity fly ash sampler produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd., also known as The fly ash constant velocity sampler or The swirling fly ash constant velocity sampler,

Working status of oil injector and main oil pump

11-25 769

The working status of The oil injector and main oil pump, The analysis of The reasons for The drop in The inlet oil pressure test of The main oil pump of a 200MW steam turbine, and The composition of The oil supply system of The 200MW steam turbine generally adopt a centrifugal main oil pump oil supply system with dual injectors.

Various forms of coal powder samplers

11-25 767

The use of carbon steel material in coal powder samplers has caused many problems, and some manufacturers still encounter These problems when using coal powder samplers. So it is recommended to use stainless steel material at least ---.

Structural form of coal powder sampler

11-25 765

The structure and working principle of The fixed coal powder sampler produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd. are mainly used for regular coal powder sampling on The secondary air coal powder pipe in The positive pressure direct blowing coal powder system.

• Previous：The basic principle of lubricating oil system injectors
• Next：Working principle of automatic steam liquid two-phase flow trap